Bluetooth: btusb: Restore QCA Rome suspend/resume fix with a "rewritten" version

Commit 7d06d58 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"")
removed the setting of the BTUSB_RESET_RESUME quirk for QCA Rome devices,
instead favoring adding USB_QUIRK_RESET_RESUME quirks in usb/core/quirks.c.

This was done because the DIY BTUSB_RESET_RESUME reset-resume handling
has several issues (see the original commit message). An added advantage
of moving over to the USB-core reset-resume handling is that it also
disables autosuspend for these devices, which is similarly broken on these.

But there are 2 issues with this approach:
1) It leaves the broken DIY BTUSB_RESET_RESUME code in place for Realtek
   devices.
2) Sofar only 2 of the 10 QCA devices known to the btusb code have been
   added to usb/core/quirks.c and if we fix the Realtek case the same way
   we need to add an additional 14 entries. So in essence we need to
   duplicate a large part of the usb_device_id table in btusb.c in
   usb/core/quirks.c and manually keep them in sync.

This commit instead restores setting a reset-resume quirk for QCA devices
in the btusb.c code, avoiding the duplicate usb_device_id table problem.

This commit avoids the problems with the original DIY BTUSB_RESET_RESUME
code by simply setting the USB_QUIRK_RESET_RESUME quirk directly on the
usb_device.

This commit also moves the BTUSB_REALTEK case over to directly setting the
USB_QUIRK_RESET_RESUME on the usb_device and removes the now unused
BTUSB_RESET_RESUME code.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 7d06d58 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"")
Cc: [email protected]
Cc: Leif Liddy <[email protected]>
Cc: Matthias Kaehlcke <[email protected]>
Cc: Brian Norris <[email protected]>
Cc: Daniel Drake <[email protected]>
Cc: Kai-Heng Feng <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>

Author: jwrdegoede

drivers/bluetooth/btusb.c

@@ -23,6 +23,7 @@
 
 #include <linux/module.h>
 #include <linux/usb.h>
+#include <linux/usb/quirks.h>
 #include <linux/firmware.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
@@ -390,9 +391,8 @@ static const struct usb_device_id blacklist_table[] = {
 #define BTUSB_FIRMWARE_LOADED	7
 #define BTUSB_FIRMWARE_FAILED	8
 #define BTUSB_BOOTING		9
-#define BTUSB_RESET_RESUME	10
-#define BTUSB_DIAG_RUNNING	11
-#define BTUSB_OOB_WAKE_ENABLED	12
+#define BTUSB_DIAG_RUNNING	10
+#define BTUSB_OOB_WAKE_ENABLED	11
 
 struct btusb_data {
 	struct hci_dev       *hdev;
@@ -3120,6 +3120,12 @@ static int btusb_probe(struct usb_interface *intf,
 	if (id->driver_info & BTUSB_QCA_ROME) {
 		data->setup_on_usb = btusb_setup_qca;
 		hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
+
+		/* QCA Rome devices lose their updated firmware over suspend,
+		 * but the USB hub doesn't notice any status change.
+		 * explicitly request a device reset on resume.
+		 */
+		interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
 	}
 
 #ifdef CONFIG_BT_HCIBTUSB_RTL
@@ -3130,7 +3136,7 @@ static int btusb_probe(struct usb_interface *intf,
 		 * but the USB hub doesn't notice any status change.
 		 * Explicitly request a device reset on resume.
 		 */
-		set_bit(BTUSB_RESET_RESUME, &data->flags);
+		interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
 	}
 #endif
 
@@ -3299,14 +3305,6 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
 		enable_irq(data->oob_wake_irq);
 	}
 
-	/* Optionally request a device reset on resume, but only when
-	 * wakeups are disabled. If wakeups are enabled we assume the
-	 * device will stay powered up throughout suspend.
-	 */
-	if (test_bit(BTUSB_RESET_RESUME, &data->flags) &&
-	    !device_may_wakeup(&data->udev->dev))
-		data->udev->reset_resume = 1;
-
 	return 0;
 }