Merge tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from Jakub Kicinski:
 "Current release - regressions:

   - arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for
     ENETC

  Current release - bugs in new features:

   - mptcp: provide rmem[0] limit offset to fix oops

  Previous release - regressions:

   - IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU
     calculations

   - lan743x: correctly handle chips with internal PHY

   - bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE

   - mlx5e: Fix VXLAN port table synchronization after function reload

  Previous release - always broken:

   - bpf: Zero-fill re-used per-cpu map element

   - fix out-of-order UDP packets when forwarding with UDP GSO fraglists
     turned on:
       - fix UDP header access on Fast/frag0 UDP GRO
       - fix IP header access and skb lookup on Fast/frag0 UDP GRO

   - ethtool: netlink: add missing netdev_features_change() call

   - net: Update window_clamp if SOCK_RCVBUF is set

   - igc: Fix returning wrong statistics

   - ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload

   - tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies

   - r8169: disable hw csum for short packets on all chip versions

   - vrf: Fix fast path output packet handling with async Netfilter
     rules"

* tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
  lan743x: fix use of uninitialized variable
  net: udp: fix IP header access and skb lookup on Fast/frag0 UDP GRO
  net: udp: fix UDP header access on Fast/frag0 UDP GRO
  devlink: Avoid overwriting port attributes of registered port
  vrf: Fix fast path output packet handling with async Netfilter rules
  cosa: Add missing kfree in error path of cosa_write
  net: switch to the kernel.org patchwork instance
  ch_ktls: stop the txq if reaches threshold
  ch_ktls: tcb update fails sometimes
  ch_ktls/cxgb4: handle partial tag alone SKBs
  ch_ktls: don't free skb before sending FIN
  ch_ktls: packet handling prior to start marker
  ch_ktls: Correction in middle record handling
  ch_ktls: missing handling of header alone
  ch_ktls: Correction in trimmed_len calculation
  cxgb4/ch_ktls: creating skbs causes panic
  ch_ktls: Update cheksum information
  ch_ktls: Correction in finding correct length
  cxgb4/ch_ktls: decrypted bit is not enough
  net/x25: Fix null-ptr-deref in x25_connect
  ...

Author: torvalds

Documentation/networking/netdev-FAQ.rst

@@ -110,7 +110,7 @@ Q: I sent a patch and I'm wondering what happened to it?
 Q: How can I tell whether it got merged?
 A: Start by looking at the main patchworks queue for netdev:
 
-  http://patchwork.ozlabs.org/project/netdev/list/
+  https://patchwork.kernel.org/project/netdevbpf/list/
 
 The "State" field will tell you exactly where things are at with your
 patch.
@@ -152,7 +152,7 @@ networking subsystem, and then hands them off to Greg.
 
 There is a patchworks queue that you can see here:
 
-  http://patchwork.ozlabs.org/bundle/davem/stable/?state=*
+  https://patchwork.kernel.org/bundle/netdev/stable/?state=*
 
 It contains the patches which Dave has selected, but not yet handed off
 to Greg.  If Greg already has the patch, then it will be here:

Documentation/networking/phy.rst

@@ -247,8 +247,8 @@ Some of the interface modes are described below:
     speeds (see below.)
 
 ``PHY_INTERFACE_MODE_2500BASEX``
-    This defines a variant of 1000BASE-X which is clocked 2.5 times faster,
-    than the 802.3 standard giving a fixed bit rate of 3.125Gbaud.
+    This defines a variant of 1000BASE-X which is clocked 2.5 times as fast
+    as the 802.3 standard, giving a fixed bit rate of 3.125Gbaud.
 
 ``PHY_INTERFACE_MODE_SGMII``
     This is used for Cisco SGMII, which is a modification of 1000BASE-X

Documentation/process/stable-kernel-rules.rst

@@ -39,7 +39,7 @@ Procedure for submitting patches to the -stable tree
    submission guidelines as described in
    :ref:`Documentation/networking/netdev-FAQ.rst <netdev-FAQ>`
    after first checking the stable networking queue at
-   https://patchwork.ozlabs.org/bundle/davem/stable/?series=&submitter=&state=*&q=&archive=
+   https://patchwork.kernel.org/bundle/netdev/stable/?state=*
    to ensure the requested patch is not already queued up.
  - Security patches should not be handled (solely) by the -stable review
    process but should follow the procedures in

Documentation/translations/it_IT/process/stable-kernel-rules.rst

@@ -46,7 +46,7 @@ Procedura per sottomettere patch per i sorgenti -stable
    :ref:`Documentation/translations/it_IT/networking/netdev-FAQ.rst <it_netdev-FAQ>`;
    ma solo dopo aver verificato al seguente indirizzo che la patch non sia
    già in coda:
-   https://patchwork.ozlabs.org/bundle/davem/stable/?series=&submitter=&state=*&q=&archive=
+   https://patchwork.kernel.org/bundle/netdev/stable/?state=*
  - Una patch di sicurezza non dovrebbero essere gestite (solamente) dal processo
    di revisione -stable, ma dovrebbe seguire le procedure descritte in
    :ref:`Documentation/translations/it_IT/admin-guide/security-bugs.rst <it_securitybugs>`.

MAINTAINERS

@@ -1279,7 +1279,7 @@ M:	Igor Russkikh <[email protected]>
 L:	[email protected]
 S:	Supported
 W:	https://www.marvell.com/
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	Documentation/networking/device_drivers/ethernet/aquantia/atlantic.rst
 F:	drivers/net/ethernet/aquantia/atlantic/
 
@@ -8830,8 +8830,8 @@ S:	Supported
 W:	http://www.intel.com/support/feedback.htm
 W:	http://e1000.sourceforge.net/
 Q:	http://patchwork.ozlabs.org/project/intel-wired-lan/list/
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue.git
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue.git
 F:	Documentation/networking/device_drivers/ethernet/intel/
 F:	drivers/net/ethernet/intel/
 F:	drivers/net/ethernet/intel/*/
@@ -11174,23 +11174,23 @@ M:	Tariq Toukan <[email protected]>
 L:	[email protected]
 S:	Supported
 W:	http://www.mellanox.com
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	drivers/net/ethernet/mellanox/mlx4/en_*
 
 MELLANOX ETHERNET DRIVER (mlx5e)
 M:	Saeed Mahameed <[email protected]>
 L:	[email protected]
 S:	Supported
 W:	http://www.mellanox.com
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	drivers/net/ethernet/mellanox/mlx5/core/en_*
 
 MELLANOX ETHERNET INNOVA DRIVERS
 R:	Boris Pismenny <[email protected]>
 L:	[email protected]
 S:	Supported
 W:	http://www.mellanox.com
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	drivers/net/ethernet/mellanox/mlx5/core/accel/*
 F:	drivers/net/ethernet/mellanox/mlx5/core/en_accel/*
 F:	drivers/net/ethernet/mellanox/mlx5/core/fpga/*
@@ -11202,7 +11202,7 @@ M:	Ido Schimmel <[email protected]>
 L:	[email protected]
 S:	Supported
 W:	http://www.mellanox.com
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	drivers/net/ethernet/mellanox/mlxsw/
 F:	tools/testing/selftests/drivers/net/mlxsw/
 
@@ -11211,7 +11211,7 @@ M:	[email protected]
 L:	[email protected]
 S:	Supported
 W:	http://www.mellanox.com
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	drivers/net/ethernet/mellanox/mlxfw/
 
 MELLANOX HARDWARE PLATFORM SUPPORT
@@ -11230,7 +11230,7 @@ L:	[email protected]
 L:	[email protected]
 S:	Supported
 W:	http://www.mellanox.com
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	drivers/net/ethernet/mellanox/mlx4/
 F:	include/linux/mlx4/
 
@@ -11251,7 +11251,7 @@ L:	[email protected]
 L:	[email protected]
 S:	Supported
 W:	http://www.mellanox.com
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 F:	Documentation/networking/device_drivers/ethernet/mellanox/
 F:	drivers/net/ethernet/mellanox/mlx5/core/
 F:	include/linux/mlx5/
@@ -12131,7 +12131,7 @@ M:	Jakub Kicinski <[email protected]>
 L:	[email protected]
 S:	Maintained
 W:	http://www.linuxfoundation.org/en/Net
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git
 F:	Documentation/devicetree/bindings/net/
@@ -12176,7 +12176,7 @@ M:	Jakub Kicinski <[email protected]>
 L:	[email protected]
 S:	Maintained
 W:	http://www.linuxfoundation.org/en/Net
-Q:	http://patchwork.ozlabs.org/project/netdev/list/
+Q:	https://patchwork.kernel.org/project/netdevbpf/list/
 B:	mailto:[email protected]
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git
@@ -15247,7 +15247,6 @@ F:	drivers/iommu/s390-iommu.c
 S390 IUCV NETWORK LAYER
 M:	Julian Wiedmann <[email protected]>
 M:	Karsten Graul <[email protected]>
-M:	Ursula Braun <[email protected]>
 L:	[email protected]
 S:	Supported
 W:	http://www.ibm.com/developerworks/linux/linux390/
@@ -15258,7 +15257,6 @@ F:	net/iucv/
 S390 NETWORK DRIVERS
 M:	Julian Wiedmann <[email protected]>
 M:	Karsten Graul <[email protected]>
-M:	Ursula Braun <[email protected]>
 L:	[email protected]
 S:	Supported
 W:	http://www.ibm.com/developerworks/linux/linux390/
@@ -15829,7 +15827,6 @@ S:	Maintained
 F:	drivers/misc/sgi-xp/
 
 SHARED MEMORY COMMUNICATIONS (SMC) SOCKETS
-M:	Ursula Braun <[email protected]>
 M:	Karsten Graul <[email protected]>
 L:	[email protected]
 S:	Supported

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts

@@ -75,6 +75,7 @@
 &enetc_port0 {
 	phy-handle = <&phy0>;
 	phy-connection-type = "sgmii";
+	managed = "in-band-status";
 	status = "okay";
 
 	mdio {

drivers/net/dsa/mv88e6xxx/devlink.c

@@ -393,8 +393,10 @@ static int mv88e6xxx_region_atu_snapshot(struct devlink *dl,
 	mv88e6xxx_reg_lock(chip);
 
 	err = mv88e6xxx_fid_map(chip, fid_bitmap);
-	if (err)
+	if (err) {
+		kfree(table);
 		goto out;
+	}
 
 	while (1) {
 		fid = find_next_bit(fid_bitmap, MV88E6XXX_N_FID, fid + 1);

drivers/net/ethernet/chelsio/cxgb4/cxgb4.h

@@ -2124,6 +2124,9 @@ void cxgb4_inline_tx_skb(const struct sk_buff *skb, const struct sge_txq *q,
 void cxgb4_write_sgl(const struct sk_buff *skb, struct sge_txq *q,
 		     struct ulptx_sgl *sgl, u64 *end, unsigned int start,
 		     const dma_addr_t *addr);
+void cxgb4_write_partial_sgl(const struct sk_buff *skb, struct sge_txq *q,
+			     struct ulptx_sgl *sgl, u64 *end,
+			     const dma_addr_t *addr, u32 start, u32 send_len);
 void cxgb4_ring_tx_db(struct adapter *adap, struct sge_txq *q, int n);
 int t4_set_vlan_acl(struct adapter *adap, unsigned int mbox, unsigned int vf,
 		    u16 vlan);

drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c

@@ -3573,6 +3573,8 @@ static int chcr_stats_show(struct seq_file *seq, void *v)
 		   atomic64_read(&adap->ch_ktls_stats.ktls_tx_complete_pkts));
 	seq_printf(seq, "TX trim pkts :                    %20llu\n",
 		   atomic64_read(&adap->ch_ktls_stats.ktls_tx_trimmed_pkts));
+	seq_printf(seq, "TX sw fallback :                  %20llu\n",
+		   atomic64_read(&adap->ch_ktls_stats.ktls_tx_fallback));
 	while (i < MAX_NPORTS) {
 		ktls_port = &adap->ch_ktls_stats.ktls_port[i];
 		seq_printf(seq, "Port %d\n", i);

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c

@@ -1176,6 +1176,7 @@ static u16 cxgb_select_queue(struct net_device *dev, struct sk_buff *skb,
 		txq = netdev_pick_tx(dev, skb, sb_dev);
 		if (xfrm_offload(skb) || is_ptp_enabled(skb, dev) ||
 		    skb->encapsulation ||
+		    cxgb4_is_ktls_skb(skb) ||
 		    (proto != IPPROTO_TCP && proto != IPPROTO_UDP))
 			txq = txq % pi->nqsets;
 

drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.h

@@ -388,6 +388,7 @@ struct ch_ktls_stats_debug {
 	atomic64_t ktls_tx_retransmit_pkts;
 	atomic64_t ktls_tx_complete_pkts;
 	atomic64_t ktls_tx_trimmed_pkts;
+	atomic64_t ktls_tx_fallback;
 };
 #endif
 
@@ -493,6 +494,11 @@ struct cxgb4_uld_info {
 #endif
 };
 
+static inline bool cxgb4_is_ktls_skb(struct sk_buff *skb)
+{
+	return skb->sk && tls_is_sk_tx_device_offloaded(skb->sk);
+}
+
 void cxgb4_uld_enable(struct adapter *adap);
 void cxgb4_register_uld(enum cxgb4_uld type, const struct cxgb4_uld_info *p);
 int cxgb4_unregister_uld(enum cxgb4_uld type);

drivers/net/ethernet/chelsio/cxgb4/sge.c

@@ -890,6 +890,114 @@ void cxgb4_write_sgl(const struct sk_buff *skb, struct sge_txq *q,
 }
 EXPORT_SYMBOL(cxgb4_write_sgl);
 
+/*	cxgb4_write_partial_sgl - populate SGL for partial packet
+ *	@skb: the packet
+ *	@q: the Tx queue we are writing into
+ *	@sgl: starting location for writing the SGL
+ *	@end: points right after the end of the SGL
+ *	@addr: the list of bus addresses for the SGL elements
+ *	@start: start offset in the SKB where partial data starts
+ *	@len: length of data from @start to send out
+ *
+ *	This API will handle sending out partial data of a skb if required.
+ *	Unlike cxgb4_write_sgl, @start can be any offset into the skb data,
+ *	and @len will decide how much data after @start offset to send out.
+ */
+void cxgb4_write_partial_sgl(const struct sk_buff *skb, struct sge_txq *q,
+			     struct ulptx_sgl *sgl, u64 *end,
+			     const dma_addr_t *addr, u32 start, u32 len)
+{
+	struct ulptx_sge_pair buf[MAX_SKB_FRAGS / 2 + 1] = {0}, *to;
+	u32 frag_size, skb_linear_data_len = skb_headlen(skb);
+	struct skb_shared_info *si = skb_shinfo(skb);
+	u8 i = 0, frag_idx = 0, nfrags = 0;
+	skb_frag_t *frag;
+
+	/* Fill the first SGL either from linear data or from partial
+	 * frag based on @start.
+	 */
+	if (unlikely(start < skb_linear_data_len)) {
+		frag_size = min(len, skb_linear_data_len - start);
+		sgl->len0 = htonl(frag_size);
+		sgl->addr0 = cpu_to_be64(addr[0] + start);
+		len -= frag_size;
+		nfrags++;
+	} else {
+		start -= skb_linear_data_len;
+		frag = &si->frags[frag_idx];
+		frag_size = skb_frag_size(frag);
+		/* find the first frag */
+		while (start >= frag_size) {
+			start -= frag_size;
+			frag_idx++;
+			frag = &si->frags[frag_idx];
+			frag_size = skb_frag_size(frag);
+		}
+
+		frag_size = min(len, skb_frag_size(frag) - start);
+		sgl->len0 = cpu_to_be32(frag_size);
+		sgl->addr0 = cpu_to_be64(addr[frag_idx + 1] + start);
+		len -= frag_size;
+		nfrags++;
+		frag_idx++;
+	}
+
+	/* If the entire partial data fit in one SGL, then send it out
+	 * now.
+	 */
+	if (!len)
+		goto done;
+
+	/* Most of the complexity below deals with the possibility we hit the
+	 * end of the queue in the middle of writing the SGL.  For this case
+	 * only we create the SGL in a temporary buffer and then copy it.
+	 */
+	to = (u8 *)end > (u8 *)q->stat ? buf : sgl->sge;
+
+	/* If the skb couldn't fit in first SGL completely, fill the
+	 * rest of the frags in subsequent SGLs. Note that each SGL
+	 * pair can store 2 frags.
+	 */
+	while (len) {
+		frag_size = min(len, skb_frag_size(&si->frags[frag_idx]));
+		to->len[i & 1] = cpu_to_be32(frag_size);
+		to->addr[i & 1] = cpu_to_be64(addr[frag_idx + 1]);
+		if (i && (i & 1))
+			to++;
+		nfrags++;
+		frag_idx++;
+		i++;
+		len -= frag_size;
+	}
+
+	/* If we ended in an odd boundary, then set the second SGL's
+	 * length in the pair to 0.
+	 */
+	if (i & 1)
+		to->len[1] = cpu_to_be32(0);
+
+	/* Copy from temporary buffer to Tx ring, in case we hit the
+	 * end of the queue in the middle of writing the SGL.
+	 */
+	if (unlikely((u8 *)end > (u8 *)q->stat)) {
+		u32 part0 = (u8 *)q->stat - (u8 *)sgl->sge, part1;
+
+		if (likely(part0))
+			memcpy(sgl->sge, buf, part0);
+		part1 = (u8 *)end - (u8 *)q->stat;
+		memcpy(q->desc, (u8 *)buf + part0, part1);
+		end = (void *)q->desc + part1;
+	}
+
+	/* 0-pad to multiple of 16 */
+	if ((uintptr_t)end & 8)
+		*end = 0;
+done:
+	sgl->cmd_nsge = htonl(ULPTX_CMD_V(ULP_TX_SC_DSGL) |
+			ULPTX_NSGE_V(nfrags));
+}
+EXPORT_SYMBOL(cxgb4_write_partial_sgl);
+
 /* This function copies 64 byte coalesced work request to
  * memory mapped BAR2 space. For coalesced WR SGE fetches
  * data from the FIFO instead of from Host.
@@ -1422,7 +1530,8 @@ static netdev_tx_t cxgb4_eth_xmit(struct sk_buff *skb, struct net_device *dev)
 #endif /* CHELSIO_IPSEC_INLINE */
 
 #if IS_ENABLED(CONFIG_CHELSIO_TLS_DEVICE)
-	if (skb->decrypted)
+	if (cxgb4_is_ktls_skb(skb) &&
+	    (skb->len - (skb_transport_offset(skb) + tcp_hdrlen(skb))))
 		return adap->uld[CXGB4_ULD_KTLS].tx_handler(skb, dev);
 #endif /* CHELSIO_TLS_DEVICE */